http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi ISDNAUDIO.COM Discussion and help forum en-us ISDNAUDIO.COM Discussion and help forum Fri, 6 Mar 2026 01:59:53 GMT http://blogs.law.harvard.edu/tech/rss YaBB 2.5 AE Revision: 1.29 30 http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1485040917/2#2 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1485040917/2#2 Thanks for the response. The TA is correct for the unit (TA301). I also get a solid green ISDN ready light on the TA so it's seeing the line ok. I'm sure it's in a configuration issue that I'm missing. I know that the RR also likes the "000" at the end of the SPIDs and have tried different iterations of that as well. The menu is a little weird compared to others so I'll probably keep going through different values to see what happens. Thanks. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1477047123/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1477047123/1#1 Hello,<br /><br />The only Prima LT I'm familiar with are the purple boxes with the yellow buttons made by Musicam USA. These don't feature any Ethernet network ports and are ISDN devices only. If you have one of those then you won't be able to use them to transport audio over Ethernet I'm afraid.<br /><br />Best regards,<br /><br />Edwin.<br /> http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1410866646/0#0 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1410866646/0#0 I have very limited knowledge of this codec despite having used one successfully for years (mostly incoming connections) I have just acquired a prima 110 which despite assurances was in full working order, will not frame incoming calls. Boots up normally. Brief displays of 'call received on line one...line two' on LCD display as usual detecting incoming calls, but apparently will not frame. As an aside..punching in the speed dial 27 (that previously I have selected to configure with Telos Zephyrs) and speed dial 1 that I have used to return to normal operation, are both greeted with the message 'SD ID NOT FOUND' on display. I have no idea specifically what tasks the codec has been used for previously. Any suggestions as to how to solve this would be appreciated. Is this a set-up issue? or a software problem? or a major hardware fault?   http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1402308957/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1402308957/1#1 Hello Karl,<br /><br />Unfortunately not, since the USB parallel port is not a "real" parallel port, but an emulated one. Having said that, what does work reliably is a parallel port PCI or PCIe card. And these don't seem to be too expensive either. <br /><br />Edwin. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1393863404/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1393863404/1#1 AudioTX Communicator will work fine with Windows 7 - the 32 bits version as well as the 64 bits version.<br /><br />Please note that you may need to check with the manufacturers of the hardware in your PC to see if they provide 64 bits drivers if you go that route. A lot of the 32 bits XP drivers will work fine in Windows 7 32 bits, but for the 64 bits version you will need 64 bits drivers as 32 bits drivers are not supported by the 64 bits version of Windows 7.<br /> http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1392719373/0#0 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1392719373/0#0 Hello  recently bought a cdqprima 110 with an TA101 interface.As i look at interface card it have an eprom that is for USA isdn lines so if anyone knows how can i convert the interface card for Europe or to buy an other 1 for europe?Ia m located at Greece so i want it to work for Greek isdn lines.Thanks. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1387546482/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1387546482/1#1 Hello Alex,<br /><br />Please double-check that the DIFs are also set to "UK" operation, although I presume that the people in New York will have checked this with you.<br /><br />If you know another studio with an ISDN line in your area then you may want to take your unit there to try it out on their line - or ask someone with a known-good unit to come and test your line. Unfortunately I know no way to make the Prima tell you what is actually wrong with the line. This is one of those cases where something more verbose than just "ISDN down" would be useful.<br /><br />We have done installations in the recent past where we were told by the line provider that the line was setup for point-to-multipoint, but when we arrived it wasn't. (We knew it wasn't setup correctly since these were AudioTX Communicator installations and Communicator provides more detail in its error messages).<br /><br />Please note that the change to point-to-multipoint is only a simple change at the branch exchange and does not require an engineer to visit you.<br /><br />Best regards,<br /><br />Edwin. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1376296074/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1376296074/1#1 Morning!<br /><br />Sorry to hear this - to me it sounds like something inside did not survive the mains failure. It could be the power supply unit, but that is hard to guess. This may be due to a spike in the supply when the mains failed, but considering the age of most of these units it could well be that it would have happened the next time you powered it on.. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1359484255/1#1 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1359484255/1#1 Hello Mark,<br /><br />It is possible that they've setup the line for point-to-point instead of point-to-multipoint. The test phone probably works with both modes, but the CDQ Prima really needs it to be point-to-multipoint. <br /><br />PS: This is just a configuration change at the exchange and should not require an engineer to visit you. <br /><br />Regards,<br /><br />Edwin. http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1358531165/2#2 ISDNAUDIO.COM Discussion and help forum/Techical support http://www.forum.isdnaudio.com/yabb2-cgi/YaBB.cgi?num=1358531165/2#2 Thanks for the reply....I thought that would be the case...so...if anyone has a suitable unwanted TA please let me know....alternatively, does anyone need a second hand CDQ1000, 1200 or 2000 ???